E-mail:[email protected]

Home >> cold work tool steel o1

cold work tool steel o1

Cold Work Tool Steel - Otai Special Steel

AISI / ASTM A681 O1 Tool Steel is a low alloy cold work tool steel that must be oil-quenched in heat treatment. Tools and dies made from O1 Flat Ground will have good wearing and abrasive qualities.

Get Price

Cold Work O1 Tool Steel 1.2510 SKS3 9CrWMn 2140 ...

Cold Work O1 Tool Steel 1.2580 SKS3 9CrWMn 2140 95MnWCr1. ASTM O1 steel is a high carbon(0.9% C), high Manganese Cold work tool steel (1.2% Mn), and with nice wear resisting properties, By the Oil quenching heat treatment can reached to 62 HRc. Oil steel O1 have Higher manganese content and chromium, tungsten content,...

Get Price

O1 Tool Steel - Oil-Hardening Cold-Work Steel (UNS T31501)

Introduction. Cold-work tool steels are high carbon steels that are further classified into three subgroups such as oil-hardening steels, high-carbon, high-chromium steels, and air-hardening steels. Oil-hardening cold-work steels are also known as group O steels consisting of O1, O2, O6, and O7 types. Type O1 oil-hardening cold-work steel consists...

Get Price

AISI O1 Cold Work Tool Steel Data Sheet

Clipping and edging tool in AISI O1 tool steel to clip and form edge of 0.036" (0.914 mm) thick stainless steel container approx. 10" x 6" x 8" (254 x 152 x 203 mm).

Get Price

O1 Tool Steel O1 Die Steel O1 Cold Work Steel

Virat Special Steels is the largest Supplier, Stockiest, Importer and Exporter of O1 Cold Work Tool Steel in India, USA and Europe.

Get Price

Cold Work Tool Steel Round Bar - saajsteel

Oil-hardening cold-work steels are also known as group O steels consisting of O1, O2, O6, and O7 types. Cold Work Tool Steel S1. S1 is an alloy shock-resisting tool steel for both hot and cold work …

Get Price

O1 Tool Steel O1 Die Steel O1 Cold Work Steel

Virat Special Steels is the largest Supplier, Stockiest, Importer and Exporter of O1 Cold Work Tool Steel in India, USA and Europe.

Get Price

AISI O1 Cold Work Tool Steel Data Sheet

of Uddeholm cold work tool steel Further information Please contact your local Uddeholm office for fur-ther information on the selection, heat treatment, application and availability of Uddeholm tool steels. MATERIAL PROPERTIES AND RESISTANCE TO FAILURE MECHANISMS Machin-ability Grade Uddeholm AISI Grindability Abrasive wear Adhesive wear AISI ...

Get Price

What O1 Steel Is And How To Work With It - Knife Up

What O1 Steel Is And How To Work With It. O1 tool steel is a cold work steel and is one of the most forgiving for making knife blades. It’s known as a low alloy steel due to the fact that it contains eight additives. The largest additive is Manganese at just 1.2%. The other minerals added are Carbon at 0.95%, Silicon at 0.4%, Chromium at 0.5%,...

Get Price

Cold Work Tool Steel - Special steel china supplier-OTAI ...

A2 Tool Steel. AISI A2 Steel is a high quality Cold work tool steel, It belong to the high quality high carbon alloy tool steel. typical applications include cold forging dies, coining dies, cold heading dies, shear blades, knurling tools and as cutting knives for paper, wood, fibre and resin-bonded aterial, etc.

Get Price

O1 Tool Steel DIN 1.2510 100MnCrW4 SKS3 - Otai ...

AISI / O1 is a low alloy cold work tool steel that must be oil-quenched in heat treatment. Tools and dies made from O1 tool steel flat or rounds will have good wearing and abrasive qualities since the tungsten and higher chromium content gives improved wear resistance.

Get Price

Cold Work Tool Steel SB Specialty Metals LLC

PSB 22 is an air hardening cold work tool steel with an excellent balance of wear resistance and toughness combined with moderate temper resistance. Rounds 1.00” diam through 9.00” diam Flats 0.500” thick through 5.00” thick. O1 view technical info. O1 is an oil hardening tool steel with moderate toughness and relatively high hardness

Get Price

Cold Work Tool Steel - risingsteel

Characteristics Rising cold work tool steel is exposed to high stresses and requires great resistance against wear, impact and bending, with increasing hardenability, permitting oil quenching with less distortion, but Rising offer high level steel material but at competitive rate, esp. the O series consists of relatively inexpensive steels, and their high carbon content produces adequate wear ...

Get Price

Cold Work Tool Steels : Total Materia Article

Figure 1 Tempering diagram of high chromium cold work steel X210CrW12. Cold work tool steels are used for gages, blanking, drawing and piercing dies, shears, forming and banding rolls, lathe centers, mandrels, broaches, reamers, taps, threading dies, plastic molds, knurling tools.

Get Price

Cold Work Tool Steel - Tool Steel-High Speed Steel China ...

SAE O1 steel is a oil quench Cold Work Tool Steel. O1 Used for manufacture of Die, stamping die, bending die, drawing die, sizing die and punch punch,Etc. JIS SKD11 Tool Steel -Japanese Cold Work Steel. SKD11 is a High Chrome-Carbon Cold Work Tool Steel Which have high hardness, high intensity.

Get Price

-1 Cold Work Die Steel - Integrated Producer of Tool …

(AISI O1) steels known as “non Chromium-1 Cold Work Die Steel WM O-1 belongs to that class of oil hardening tool -deforming” steels. It will develop full hardness on oil quenching from a relatively low temperature, with minimum volume change. The high manganese content imparts good non-deforming properties, and the addition

Get Price

O1/1.2510 Cold Work Tool Steel, Alloy Tool Steel,Oil Steel

O1/1.2510 Cold Work Tool Steel, Alloy Tool Steel,Oil Steel

Get Price

Tool Steel LescoWearl LescoWear Technical Data

Lescowear™ Cold Work Tool Steel. Quenching Cool in still to 150-125°F (66-51°C). Tempering Temper immediately after quenching. Hold at temperature for 1 hour per inch (25.4 mm) of thickness, 2 hours minimum, then air cool to ambient temperature. Typical tempering temperatures are 950 to …

Get Price

O1 Tool Steel - West Yorkshire Steel - Special Steel

O1 tool steel stockholders and suppliers, delivering to the whole of the UK. West Yorkshire Steel are stockholders and suppliers of O1 tool steel round bar, flat bar and plate. This grade is an oil hardening tool steel type supplied in the annealed condition.

Get Price

Tool Steel Rounds Flats - A2, A6, D2, H13, O1, L6, S1, S5, S7

O1 Tool Steel Rounds / Flats (A.K.A. 01 Tool Steel) O1 is an all-around general purpose oil-hardening tool steel that is characterized by reliable hardening, very good machinability, good wear resistance, and sufficient toughness for a wide variety of tool and die applications.

Get Price